Local Services

Trailer Repair Shop East Irvine CA

Rv Camper Repair Near Me East Irvine

Published Jun 09, 25

12 min read

Table of Contents

– Camper Trailer Service Near Me East Irvine, CA
– OCRV Center
– Camper Services East Irvine, CA
– Camper Roof Repair East Irvine, CA
– Rv Camper Repair Near Me East Irvine, CA
– Pop Up Camper Repair East Irvine, CA
– Camper Awning Repair East Irvine, CA
– Camper Repair Places Near Me East Irvine, CA
– Rv Camper Ac Repair East Irvine, CA
– Camper Roof Replacement East Irvine, CA
– Camper Repair East Irvine, CA
– Camper Services East Irvine, CA
– Camper Service East Irvine, CA
– OCRV Center

Camper Trailer Service Near Me East Irvine, CA

OCRV Center

23281 La Palma Ave Yorba Linda, CA 92887
(714) 909-1444
OCRV Center

(I really did not have the locking handles tightened up down.) I didn't see anything wrong, but withdrawed both awning just to be secure. Many campers around us had their awnings released. We returned home the other day in the rain, so today I released the awnings to dry them out. That's when I uncovered that the gutter had been retreated from the wall surface (and downspout was missing) on the right-hand man end of the front awning.

It appears that regarding 18 to 24 inches of the steel extrusion (gutter) that the awning is glided right into has pulled away from the wall surface and twisted a little bit - Rv Camper Repair Near Me East Irvine. I'm thinking the repair service will require replacing that entire length of rain gutter (10 feet?) and possibly utilizing larger gauge screws to change those that were taken out

We've got damaged brackets on our camper awning. Two months earlier, we had a negative tire blow-out that created a curved axle, significant fixings, and so on, and we ask yourself if the brackets cracked/broke throughout the bouncy experience before we recognized the axle remained in problem. We have not had the awning out considering that it remained in the shop to be repaired.

Camper Services East Irvine, CA

The awning itself, spring system, and so on, is fine. The back brace assembly is fine, but the front one is fractured at the bottom and completely broken through at the top, so that the top support arm no longer fastens to the camper.

Does this audio affordable? Even the real support arms are undamaged. They are white metal (? aluminum?) and the braces are a larger gray steel - it's the grey little bits that have cracked/broken. The real arms are entirely normal/functionalI'm just wanting to see to it we're not being absorbed out of our desperation.

Camper Roof Repair East Irvine, CA

The Recreational vehicle is a 2007, however we had rainfall damage in 2010 and the entire awning was brand name new at that time. If absolutely nothing else, we would like advice as to exactly how we can "jerry rig" this for a while - maybe also obtain us through the summer season - without having to put in a brand name new awning!

If we have to go awning-less, we will, but I prefer to locate a quick and reliable solution. Anyone? Please!.

Welcome to my Recreational Vehicle Renovation Series!.?.!! I get on action 5 of changing the roofing of my '93 Fleetwood Jamboree Searcher motorhome. In the last step I eliminated the roofing system trim molding from three sides of the roof. Yet in order to eliminate the fourth one, I require to eliminate the motor home awning as well.

In order to replace the rubber roofing and roof outdoor decking, I need to eliminate the awning. My recreational vehicle awning has legs which pivot at the base however can be removed to set on the ground. First I pulled these out. Pushing this bar launches the foot of the awning legs.

Rv Camper Repair Near Me East Irvine, CA

You'll also see just how the brace is hooked on top of the trim molding that holds back the fiberglass panel in the back corner. That's why the awning requires to find off initially before the last actions of this blog post (revealing the front and back sides of the roof covering decking).

Below's a detail of exactly how the awning placing brackets are screwed right into the camper. I really did not actually have to do this action until the awning was on the ground but I discovered this set screw here holding the awning canvas into the awning rail (there's one more at the right end of the awning.) I proceeded and loosened it.

Once both screws are gotten rid of, merely draw back on the bracket. Unscrewing the huge lag screws that hold the RV awning placing brackets to the camper (with an outlet wrench) Getting rid of the mounting bracket once the lag screws have been unscrewed. Note exactly how this end was hooked over the termination bar that secures the spherical edge at the back of the roofing.

Both lag screws eliminated from the awning placing bracket on the right. Eliminating the mounting bracket of the awning. When the installing brackets are removed, it's time to get rid of the awning rail. Keep in mind, the awning rail is generally similar to a routine item of light weight aluminum roofing system side trim molding except that near the bottom side there is a circular track with a port in it.

Pop Up Camper Repair East Irvine, CA

To change the roof, this awning bar requires to be gotten rid of. Here's a look at the round channel at the end of the awning rail. The canvas for the awning slides into this track. Heads up! If you're just changing your awning and not repairing the entire roofing system like me, after that you wouldn't require to get rid of the awning rail.

Dropping the legs a couple of notches to reduce the entire awning. Now I can reach this trim molding (the awning rail) easily. Now it's just like removing the side trim molding on the various other side of the camper. Take out the plastic insert that covers the screw heads (you might have to reduce completion with an utility knife if it is tucked under the rail) and after that just pull it out.

You might have to cut the end with an energy knife if it is wrapped under. Simply pull it out!

Once the screws were out I began spying up the awning rail. (There will be some butyl tape or putty sticking it to the rubber under.) DIRECTS! When I began to tear off the awning rail, the whole thing unexpectedly snapped off and rolled up right into the awning like a window blind.

Camper Awning Repair East Irvine, CA

Simply understand it's coming! Once the screws are removed, the awning rail can be pried up. You can see the side of the rubber roof covering that was secured under it. Once you begin drawing the awning rail away it will instantly snap totally free and roll up like a home window blind with the awning.

This thing is hefty so if you're working alone like me after that lower it the ground bit by bit by strolling the legs away from the camper on each side individually till you can lay it on the ground. I flipped the legs back up and out of the way versus the camper.

Then I leaned the legs back against the camper. Once the awning was on the ground I got rid of the little collection screw at the best end of the awning, (I removed the one at the left end previously.) These screws keep the awning canvas from sliding in the rail. Once they're gotten rid of the rail just moves right off the canvas by moving the entire rail away.

Camper Repair Places Near Me East Irvine, CA

When both set screws were eliminated I might slide the entire awning rail straight off the awning. Review at the account of this trim molding (the awning rail) after it was removed. Woo hoo! The awning is off! The last step prior to I can get rid of the old roof covering decking is to expose the ends of it where the fiberglass panels overlap it at the front and rear of the camper.

The next thing holding down the rv fiberglass exterior siding panels is the edge trim molding shown here. It has a plastic screw cover strip inserted, so once more I simply pried up the plastic insert and drew out sufficient so I might loosen some screw heads.

I might end up eliminating it later on if I require to replace the luan plywood under this fiberglass change. The roof covering decking plywood expands under the fiberglass skin at the back of the camper. In order to change it, this fiberglass shift have to be lifted. To lift that, the edge molding must be removed.

After that I might swing the trim mold and mildew off the side sufficient to lift up the side of the fiberglass panel. Once I can swing that piece of edge molding off the side, I started to pry up the fiberglass panel. It has glue under it and littles rusted staples and sheared off screws still holding it in position.

Rv Camper Ac Repair East Irvine, CA

I switched from a scraper to a tight 6 vast putty blade. This item cracked out of the fiberglass panel when I was trying to pry it up. Then I switched over from a scrape to 6 inch vast taping knife. After that I loosened up the other edge trim in the same method, and curved it sidewards just sufficient to ensure that I could raise up the edge of the fiberglass panel.

I discovered a lot of water damage in the plywood under the fiberglass panel so I'll possibly be changing it. Which suggests I'll finish eliminating those edge trim pieces right down nevertheless. We'll obtain to that later on. I had a considerable quantity of water damage in the joint between the rounded corner and the roof deck.

Camper Roof Replacement East Irvine, CA

The edge of the roofing system outdoor decking is subjected at the back of the camper! I've revealed the roof substratum at the back side of the camper. Currently its time to locate the front side.

Once again, I pried that layer up as well (there had not been much stifling yet glue now) and afterwards I might yank out the rest of the rubber roof that was glued underneath it. Now I can take out the last little rubber roofing from underneath the fiberglass and luan plywood.

Camper Repair East Irvine, CA

I discovered there were no bolts holding the roofing plywood down. I could see the blue styrofoam insulation beneath the harmed locations of luan plywood on the roofing. Notice there are no bolts at all holding down the roofing system plywood!

Once I scuffed up several of the damaged bits I acquired a strong piece of plywood and began to draw. The entire thing began to pull up easily in one piece without damaging the foam board insulation at all. Currently I might see the steel framing under. But after that the plywood began peeling off up as one piece, leaving all the styrofoam well intact.

There is a metal reinforced tape under that signs up with the items together. I do not understand exactly how exactly they handled to adhesive whatever down so well and get this tape joining them from the bottom, but it was nicely done. The items of roofing ply are collaborated at the seams beneath with a metal-reinforced tape.

Camper Services East Irvine, CA

I rapidly realized the roofing system was losing strength and stiffness as I drew up the leading layer, so split it off prior to the initial seam. A close up of the metal framework in the roof covering: one inch wide, one and a fifty percent inches tall. Right here's an information of the wiring in the insulation foam and the solid timber supports where the antennas screw right into the roofing system.

Camper Trailer Repair Near Me East Irvine, CA

I found a number of water damages in the plywood under the fiberglass panel so I'll probably be replacing it. Which means I'll end removing those corner trim pieces right down besides. Yet we'll reach that later. I had a significant amount of water damages in the joint between the rounded corner and the roofing deck.

The side of the roof covering outdoor decking is revealed at the back of the camper! I've revealed the roof substrate at the back side of the camper. Now its time to discover the front side.

Once more, I pried that layer up too (there had not been much quieting however glue now) and afterwards I could tug out the rest of the rubber roofing that was glued below it. Rv Camper Repair Near Me East Irvine. Now I can draw out the last little bit of rubber roof from beneath the fiberglass and luan plywood

Camper Service East Irvine, CA

Camper Repair Shop Near Me East Irvine, CA

I saw there were no fasteners holding the roof plywood down. I might see the blue styrofoam insulation below the harmed areas of luan plywood on the roofing. Notification there are no bolts at all holding down the roof plywood!

As soon as I scuffed up a few of the busted bits I obtained hold of a strong item of plywood and started to draw. The entire thing began to draw up cleanly unscathed without harming the foam board insulation in all. Currently I could see the steel framing beneath. Then the plywood started peeling off up as one item, leaving all the styrofoam well intact.

There is a steel strengthened tape under that joins the assemble. I don't know how specifically they handled to adhesive every little thing down so well and get this tape joining them from the underside, however it was nicely done. The items of roofing ply are collaborated at the seams below with a metal-reinforced tape.

OCRV Center

Address: 23281 La Palma Ave Yorba Linda, CA 92887
Phone: (714) 909-1444
OCRV Center

I quickly recognized the roofing system was losing strength and tightness as I brought up the leading layer, so split it off simply prior to the initial joint. A close up of the metal framing in the roof covering: one inch wide, one and a half inches tall. Below's an information of the electrical wiring in the insulation foam and the strong timber reinforcements where the antennas screw right into the roofing.

Share us on...

Table of Contents

– Camper Trailer Service Near Me East Irvine, CA
– OCRV Center
– Camper Services East Irvine, CA
– Camper Roof Repair East Irvine, CA
– Rv Camper Repair Near Me East Irvine, CA
– Pop Up Camper Repair East Irvine, CA
– Camper Awning Repair East Irvine, CA
– Camper Repair Places Near Me East Irvine, CA
– Rv Camper Ac Repair East Irvine, CA
– Camper Roof Replacement East Irvine, CA
– Camper Repair East Irvine, CA
– Camper Services East Irvine, CA
– Camper Service East Irvine, CA
– OCRV Center

Local Services

Navigation

Home